山东LECO分析仪

ONH836氧氮氢分析仪

高频燃烧红外检测技分析无机材料中的碳、硫含量。

采用惰性气体保护熔融法，提供各种无机材料、钢铁、有色金属、硬质合金、难熔金属、陶瓷等材料中宽范围的氧氮氢同时分析。

该仪器配置MS Windows®的软件接口，专为触摸屏操作定制。长期的开发研究与客户反馈相结合，这个简单方便的软件使得用户可以快速完整访问仪器控制，分析设置，故障诊断，数据报告， **提高日常分析的效率并节省用户宝贵的时间。 可选的Cornerstone® Mobile软件功能，使得用户可以在手机，便携式电脑及台式电脑上便捷的访问仪器数据，分析曲线图形以及仪器的状态，实现对仪器的遥控。

减少了繁琐的额外数据处理。山东LECO分析仪

氧氮氢分析仪的常见故障及解决方法

仪器启动时显示。没有水流。系统分析电流切断，分析停止。这是水流探测器不正常，水泵不工作，管道堵塞。将仪器的右面板取下，观察水流探测器，用手挤压补水塑料水瓶，发现水流正常，显示正常，证明水流探测器正常，管道畅通。启动循环水泵，但分析仪显示没有水流，此时可判定水泵不正常。打开水泵转子密封口，启动泵发现电机正常运转，此时关闭进水，拆下水泵，发现叶轮脱落。经了解，判定是由于外部冷却水停水，仪器内循环水温过高（水温应≤70℃），致使叶轮（叶轮材料PVC）热胀并脱轴。用粘合剂粘合叶轮后再粘于叶轮轴上，待粘合剂凝固后试车，仪器运行正常。 新疆LECO分析仪哪家好配置SmartLine® Remote远程诊断功能。

Determine the instrument blank.

a. Login a minimum of 3 Blank replicates.

b. Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open.

c. Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

d. Clean the upper and lower electrode manually, or, if applicable, remove thecrucible and press the analyze button to clean with the automatic cleaner.

e. Firmly place a graphite crucible on the lower electrode tip.

f. Press the Analyze button on the instrument screen, the lower electrode will close and the analysis sequence will start and endautomatically.

g. Repeat steps 2b through 2f a minimum of three times.

h. Set the blank following the procedure outlined in the operator's instruction manual.

Sample Preparation

Sampling and sample preparation is an important issue because traditional methods used to obtain samples for oxygen and nitrogen determination are different from those recommended for hydrogen, especially when sampling molten metal. The main difference in steel sampling procedures for oxygen/nitrogen and hydrogen is due to the mobilityof hydrogen. Special precautions must be used when sampling for hydrogen. From molten steel and iron, a sample must be quickly quenched in cold water and chilled in a refrigerant such as liquefied nitrogen or a mixture of acetone and solid carbon dioxide in order to reduce losses of hydrogen from diffusion. Losses of oxygen and nitrogen from diffusion are not a problem. A sample that is taken for hydrogen and

chilled in a refrigerant can also be used for oxygen and nitrogen determination. However, a sample that is typically taken for oxygen and/or nitrogen determination is not suitable for hydrogen determination due to hydrogen loss (diffusion). Surface contamination must be removed by filing or light grinding, using care not to overheat the sample.

氧氮氢分析仪怎么选？欢迎联系上海禹重科技，我司产品质量保证，欢迎咨询！

Procedure – Powder/Chip Samples

Instrument calibration/drift correction.

Press the Analyze button on the instrument screen. After a short delay, the loading head slide-block will open.

Place the Nickel Capsule containing the sample into the open port at the top of the loading head.

Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

Clean the upper and lower electrode either manually or remove the crucible and press the analyze button to clean with an automatic cleaner if applicable.

20位试样自动进样系统。山东LECO分析仪

氧氮氢分析仪的使用注意事项：

1 、氧氮氢分析仪在初次启用前，应该对连接点、焊点、阀门等进行检漏，以确保空气中的氧不会反渗进入管道及仪器内部，造成测量数值偏高。

2、再次使用仪器前，要进行管道系统净化，将漏入的空气除干净，同时确保连接取样管路时没有漏入空气。

3、样气中氧含量的变化会受管道材质及表面粗糙度影响，因此一般连接管路选用铜管或抛光过的不锈钢管，而不用塑料管、橡胶管等。

4、微量元素分析时，要避免各种管件、阀门、表头等死角对样气造成污染，因此必须尽可能的简化气路系统，连接件死角要小，以防止溶解氧逸出造成污染，使用水封、油封及腊封等设备，才能较好的确保数据的。

山东LECO分析仪